Browse SAE J ORFS O-Ring Face Fittings in the World Wide Metric, Inc. catalog including Nuts and Rings,Equal Fittings,Male Stud Coupling,Bulkhead. The Seal-Lok fitting meets or exceeds the strict requirements of SAE J and ISO It is an O-ring face seal type fitting that consists of a nut, a body. Thread Specification – ORFS (SAE J). TECHNICAL DATA. SAE J, ISO ORFS is O RING FACE SEAL. ORFS system consists of ORFS.

Author: Gokinos Dojinn
Country: Guyana
Language: English (Spanish)
Genre: Photos
Published (Last): 15 September 2011
Pages: 134
PDF File Size: 1.75 Mb
ePub File Size: 13.1 Mb
ISBN: 357-9-18339-372-5
Downloads: 53310
Price: Free* [*Free Regsitration Required]
Uploader: Kagami

Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed sae j1453 guaranteed minimums.

This standard is available for individual purchase. This Standard References Showing 10 of Sae j1453 three parts of SAE J cover material, dimensional, and performance requirements of steel O-ring face seal ORFS connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies sae j1453 nominal tube sas of 6 mm through 50 mm.

Identify unmet needs and discover next-generation technologies Improve quality by leveraging consistent standards to meet customer and market requirements Sae j1453 risk: Field of Application These connectors are intended for general application see Figures 3, 4, and 5 and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to sae j1453 leakage and variations in saae procedures.

TOP Related  I LOVE YOU KUYA WATTPAD EBOOK

Top Categories Terms of Use. SAE J covers the requirements for O-ring face seal connectors to sae j1453 stud ends along with the associated adapters, bulkhead and union connectors.

Purpose The three parts of SAE Sae j1453 cover material, dimensional, and performance requirements of steel O-ring face seal ORFS connectors for tubing and the O-ring face sae j1453 interface and nut portion of hose stem assemblies for nominal tube diameters of 6 mm through 50 mm.

In the past, these connectors have been used predominantly with inch tubing. These connectors are intended for general application see Figures 3, 4, and 5 and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage sae j1453 variations in assembly procedures.

For any application, it is recommended that sufficient testing be conducted and reviewed by both the sae j1453 and manufacturer to ensure that required performance levels are met. Speed up research, capture and reuse expertise For additional product information, visit the IHS Standards Expert page.

ORFS MALE O-RING SEAL ISO SAE J hydraulic test fittings – Ruihua Hardware

IHS Standards Expert subscription, simplifies and expedites the process for finding and managing standards by giving you access to standards from over standards developing organizations SDOs. Mitigate liability and better understand compliance regulations Boost efficiency: Sae j1453 rated working pressure of a fluid conductor assembly using SAE J hose stem connections or formed tube or braze-on tube connections shall not exceed rated working pressure of the lowest rated component thereof.

TOP Related  BRILLIANCE OF THE SEAS DECK PLANS EBOOK

For use of these connectors in conditions outside the pressure and temperature limits specified, the manufacturers must be consulted. Both metric and inch tubing can be accommodated by sae j1453 only the sleeve sae j1453 match the tube diameters.

Click here to skip or ad will close in 15 seconds.

Price and Buy this Standard View Pricing. For new designs metric tubing should be considered. These sae j1453 are capable of providing leak proof j4153 flow connections in hydraulic systems operating from 95 kPa vacuum to working pressures shown in Table 4. Sae j1453 hex dimensions of parts will be moved from the main document to an informative annex after